AWB2010-B, Anybus Wireless Bolt Serial - Black versionAWB2010-BThe Anybus Wireless Bolt Serial - Black connects serial machines to wireless networks via Bluetooth® or Wi-Fi., The versatile Bolt can function as an Access Point in multi-point applications, facilitating connections for up to seven clients simultaneously. wifi4;bluetooth;bluetoothle, Anybus Wireless Bolt Serial - Black version

This means that several of the newly discovered design flaws have been part of Wi-Fi since its release in 1997., Fortunately, the design flaws are hard to abuse because doing so requires user interaction or is only possible when using uncommon network settings., Conclusion regarding Anybus products Anybus Wireless Bridge and Anybus Wireless Bolt based on ODIN-W2 are potentially vulnerable only to a subset of the attacks known as FragAttacks as listed below., Referenced part numbers AWB3000-B AWB3000-B- 10PACK AWB3003-B AWB3300-B AWB3010-B AWB3010-B- 10PACK AWB3100-B AWB3101-B AWB3110-B AWB3120-B AWB3130-B AWB3131-B AWB3132-B AWB2000-B AWB2000-B- 10PACK AWB2000-B- RJ45PACK AWB2001-B AWB2001-B- 10PACK AWB2300-B AWB2010-B AWB2010-B- 10PACK AWB2011-B AWB2011-B- 10PACK AWB2020-B AWB2020-B- 10PACK AWB2021-B AWB2021-B- 10PACK AWB2305-B AWB2306-B AWB2310-B AWB2400-B AWB2030-B AWB2030-B- 10PACK AWB2031-B AWB2031-B- 10PACK AWB2330-B AWB2401-B- 10PACK Severity / CVSS Score - HMS Recommendations HMS recommends to observe the HMS Security Advisory web www.hms-networks.com/cybersecurity for any news regarding these vulnerabilities., Page 2 of 2 HMSSAR-2021-07-02_001 HMS Security Advisory Report Head office: HMS Industrial Networks AB | Stationsgatan 37, Box 4126, SE-300 04 HALMSTAD |www.hms-networks.com Phone: +46 35 17 29 00 | Fax: +46 35 17 29 09 | Mailing address: P.O BOX 4126, SE 300 04 HALMSTAD Product updates HMS will provide a firmware update to overcome the referenced vulnerabilities.

APPLICABLE PRODUCTS Anybus Wireless Bolt - Ethernet 18-pin (AWB2000) Anybus Wireless Bolt Serial (AWB2010) Anybus Wireless Bolt CAN (AWB2020) Anybus Wireless Bolt - Ethernet RJ45 PoE (AWB2030) Anybus Wireless Bridge II - Ethernet (AWB3000)   ISSUE / QUESTION / SYMPTOM After setting both devices to an appropriate Easy Config mode and waiting 120 seconds, the devices aren't configured as expected., Timing After applying an Easy Config mode, the device will wait 120 seconds to discover or be discovered by another Bolt/Bridge., For that reason, it can be helpful to connect both devices to a computer so that both can be configured in quick sequence.  , Location Both Bolt/Bridge devices must be positioned within range of each other., ADDITIONAL INFO Visit the Files and Documentation page for setup guides, manuals, and firmware updates: Anybus Wireless Bolt - Ethernet 18-pin (AWB2000) Anybus Wireless Bolt Serial (AWB2010) Anybus Wireless Bolt CAN (AWB2020) Anybus Wireless Bolt - Ethernet RJ45 PoE (AWB2030) Anybus Wireless Bridge II - Ethernet (AWB3000)  , Troubleshooting Anybus Wireless Bolt/Bridge Setup With Easy Config

APPLICABLE PRODUCTS Anybus Wireless Bridge II - Ethernet (AWB3000 and AWB3010)  Anybus Wireless Bolt - Ethernet RJ45 PoE (AWB2030)  Anybus Wireless Bolt Serial (AWB2010)  Anybus Wireless Bolt CAN (AWB2020)  PRE-REQUISITES Connection to the Anybus Wireless device configuration page At least one Bluetooth device in discovery mode and within range IN THIS ARTICLE  Bolt Configuration Best Practices AT Commands Additional Info   BOLT CONFIGURATION BEST PRACTICES: There are some best practices for setting the Bolt up for Bluetooth connections., WLAN (WiFi) should be disabled if it is not being used to save valuable resources, like memory and wireless bandwidth., To disable WLAN, the ‘Enable’ check box in the ‘WLAN Settings’ section should be unchecked., AT COMMANDS: If a Bolt is scanning for a non-Anybus Bluetooth device and unable to find it, or getting the “Error, couldn’t scan for any Devices” error, it may be because the Bolt is only searching for other Anybus devices.  , The Bolt uses a device filter to only search for other Anybus devices by default., Anybus Wireless scan not finding Bluetooth devices

APPLICABLE PRODUCTS Anybus Wireless Bridge II - Ethernet (AWB3000 and AWB3010)  Anybus Wireless Bolt - Ethernet RJ45 PoE (AWB2030)  Anybus Wireless Bolt LTE (AWB1500)  Anybus Wireless Bolt IoT (AWB1000)  Anybus Wireless Bolt Serial (AWB2010)  Anybus Wireless Bolt CAN (AWB2020)  ISSUE IPConfig does not find Wireless Bolt or Bridge   POSSIBLE CAUSES Make sure the latest version of IPConfig is installed: The latest version can be download here or from https://www.anybus.com/support.  , Make sure the utility is scanning the correct adapter/interface: Select the gear icon in the upper right-hand corner: A specific interface to scan with or all interfaces can be selected: When the Bolt/Bridge is found, it can be selected to change its IP configuration, if necessary, so that the web interface can be reached.  , Verify that the Bolt is powered on and the LEDs are lit up (these can be seen through the reset hole on the bottom of the Bolt)., In the Network Adapters list, other active adapters can be temporarily disabled (including WiFi): If the problem persists, the Bolt should be reset to it's default settings., The web interface should now be manually accessible using a browser., IPConfig doesn't find Wireless Bolt or Bridge

Cabling Before You Begin NOTE When using Easy Config Modes, the Bolt Serial that is to be configured as a Client does not need to be connected to the Ethernet wires., Bolt Serial Built-In Web Interface The Bolt Serial built-in web interface is used to configure, maintain and troubleshoot the Bolt Serial., Configuration of Wireless Bolt and Bridge Clients can be performed wirelessly, via a PC connected to the Wireless Bolt or Bridge Access Point., Te c h n i cal Specifications Order code AWB2010 AWB2011 Color Black White top and black base Connector Included plug connector (2x9p; 3.5mm, Phoenix DFMC 1.5/9-ST-3.5, push-in spring connection)., Anybus ® Wireless Bolt Serial ™ Technical Data Page 24 of 28 SP2554 2.0 Order code AWB2010 AWB2011 Humidity compatibility EN 600068-2-78: Damp heat, +40°C, 93% humidity for 4 days., Startup Guide - Anybus Wireless Bolt Serial

Reset button The Reset button is located on the bottom of the Bolt Serial., Reset button The Reset button is located on the bottom of the Bolt Serial., Te c h n i cal Specifications Order code AWB2010 AWB2011 Color Black White top and black base Connector Included plug connector (2x9p; 3.5mm, Phoenix DFMC 1.5/9-ST-3.5, push-in spring connection)., C l a s s i c B l u etooth Wireless standards (profiles): PANU & NAP Operation modes: Access point or Client Anybus ® Wireless Bolt Serial ™ Technical Data Page 52 of 60 SCM-1202-143 2.0 Order code AWB2010 AWB2011 RF output power: 9.75 dBm Max number of slaves for Access Point: 7 Power consumption: 36 mA@24VDC Net data throughput: ~1 Mbps Bluetooth version support: Classic Bluetooth v2.1 Security: Authentication & Authorization, Encryption & Data Protection, Privacy & Confidentiality, NIST Compliant, FIPS Approved Technical Specifications Anybus ® Wireless Bolt Serial ™ SCM-1202-143 2.0 Page 53 of 60 11., The Bolt is mounted in a metal cabinet illustrated by the yellow box below the Bolt., User Manual - Anybus Wireless Bolt Serial